Авто & Тээврийн хэрэгсэл

Here's How I Will Save My Blown BMW Supercar Engine using Scrap Parts off a Mini Cooper

Get over 68% off the Kove Commuter 2 here: koveaudio.com/sc68
Code SC68 (works site wide)
We've got a way to save our Cheap BMW i8 Supercar's Blown Engine without replacing it and spending over $10,000 on a new one, but will it work? Also, Rich sends Sam something to help him along the way; credit goes to Anthony Jeselnik who created this bit!
For service on your European Car check out Eurocharged Orlando Florida: eurochargedorlando/ or call (407) 960-4517
Instagram: samcracc​
Email Me: SamcracAuto@gmail.com

Сэтгэгдлүүд 

  1. bullcrapptv

    bullcrapptv

    5 өдрийн өмнө

    Jeselnik did the bible joke using his grandmother.

  2. OSCARRZ FILMS

    OSCARRZ FILMS

    7 өдрийн өмнө

    4:31 “IS THAT A SUPRAAAAAAA???!!!”

  3. SkippingRhyme

    SkippingRhyme

    7 өдрийн өмнө

    11:16 I see you also thought, "Fuck it ill just get a Cooper Motor and turbo charge it!" LMAO

  4. Aaron Kuehner

    Aaron Kuehner

    8 өдрийн өмнө

    You have me yelling at the screen. "READ THE BIBLE!" xD

  5. Aaron Kuehner

    Aaron Kuehner

    8 өдрийн өмнө

    DUUUUUUUDE!!! You have the best ad rolls EVER! Seriously, you continue the show and still have solid product placement. Radio product placements SUCK compared to your efforts. I seriously have stopped listening to live radio, decades ago, because of their suck-ass product chats. On top of that all, your videos are friggin' solid. You have my vote for being a great director. P.S.: Just saw GTOger's comment and upvoted. This is entertainment.

  6. adam jankowski

    adam jankowski

    10 өдрийн өмнө

    .005" is too much to surface on the head?.... lol 😆 they sure as hell don't build them like they use too. 🤣

  7. diecast jam

    diecast jam

    10 өдрийн өмнө

    This is a rare car, you know almost certainly someone will still be driving it in 50 years time, so following that line of logic it's probably not going to be with this engine, my point is someone at some point in the future is going to bite the bullet and replace the engine. Just look at how much the original M1 is going for, I mean the 70's sports car here, and that'll give you an idea of what these will be worth in 10-15 or 20 years time.

  8. Pedro’s Car Life

    Pedro’s Car Life

    15 өдрийн өмнө

    Sam has a dui

  9. NightWaves

    NightWaves

    16 өдрийн өмнө

    Don't be a fool like so many guys that think downshifting an engine with the rpms low to engine brake is cool. That's the biggest head gasket blower anywhere. It's common to have different head gasket thicknesses. Just shave the head. Make sure you get some rpms up before letting out the clutch downshifting.

  10. Regelos

    Regelos

    18 өдрийн өмнө

    Oh my youthful years when I would DUI my straight edge

  11. #Artzi _Ip#

    #Artzi _Ip#

    19 өдрийн өмнө

    that was like 1mm thick caliber used with the block :D normally should use 0.1 mm thick

  12. Tex Moto

    Tex Moto

    19 өдрийн өмнө

    another often overlooked issue with warped head id the the bottom surface isn't the only dimension that changes. The cam journals are line bored as a set, when the heat warps the head it also moves the cam journal out of alignment slightly and those should also be checked for alignment if the warpage is significant. Saw this a in 90s Honda engines and larger straight 6 like the RB or 2J that were ran too hot.

  13. ingShorty

    ingShorty

    20 өдрийн өмнө

    I've heard of this same story with the book... love these storiez.

  14. ingShorty

    ingShorty

    20 өдрийн өмнө

    LET'Z GOOOOOOOO MI GUY

  15. paspax

    paspax

    22 өдрийн өмнө

    Hylomar.

  16. APD Shadow

    APD Shadow

    22 өдрийн өмнө

    so non car mechanic question. would it have been possible to have machined the head and block down then used some sort of a shaped plate as say a shim to equal the original manufactured tolerance on piston travel distance? why or why not.

  17. Vankai

    Vankai

    23 өдрийн өмнө

    please.. that flute/guitar instrumental.. i think its s remix of somthing.. please..what is is called??

  18. jerry Hunsucker

    jerry Hunsucker

    24 өдрийн өмнө

    Ok I smell a rat ! Nobody but nobody has this much car trouble . nice try . 😄

  19. Groningen Paranormaal

    Groningen Paranormaal

    26 өдрийн өмнө

    FunFact, did anyone els see a spirit orb fly next that dude on his left when he starts laughing about the book at 2:17 .. Don't laugh to hard cause it was heard :)

  20. helt murings

    helt murings

    27 өдрийн өмнө

    can u please do an update on the Ferrari 360?!

  21. porscheoscar

    porscheoscar

    29 өдрийн өмнө

    only 760k views? those are rookie numbers. you subscribers are miserable

  22. Go For The Gold

    Go For The Gold

    29 өдрийн өмнө

    I wish you can skip what that cylinder head guy say and resurface it away...I bet you it would probably be ok.

  23. George Cupac

    George Cupac

    Сарын өмнө

    As a ford guy.... Do an LS swap 🤣

  24. andrew munz

    andrew munz

    Сарын өмнө

    nobody uses inches any more, it was obsolete in 1972

  25. andrew munz

    andrew munz

    Сарын өмнө

    EPIPHANY! Weld the cylinder to the block! easy fix?

  26. andrew munz

    andrew munz

    Сарын өмнө

    is it the " squish?" can you add shimms? welding? can you electro depas.... something that builds metal?

  27. Mike G

    Mike G

    Сарын өмнө

    If a car has interchangeable parts with a Mini Cooper, it's NOT A SUPERCAR! 🤣😂 You make enough money on this channel alone to easily pay for a $10k motor, quit hamming it up and creating fake drama you schmuck. EDIT: This guy has Adam Gase eyes.

  28. Jimmy James

    Jimmy James

    Сарын өмнө

    Dude, how many frickin videos you going to post for this piece of crap?

  29. OldSilver Drew

    OldSilver Drew

    Сарын өмнө

    A 'supercar' with a 3 cylinder engine?

  30. Tom Hall

    Tom Hall

    Сарын өмнө

    5 thou is nothing, just chop it down, the machine shop just didn't want to be responsible for any potential problems. Which there won't be.

  31. Sherie Oshon

    Sherie Oshon

    Сарын өмнө

    That look like xxxtention car not going to lie

  32. Michael Lehmann

    Michael Lehmann

    Сарын өмнө

    That machine shop heard BMW I8 and just didn’t want to get involved. He stopped at .005”. There is no problem with taking .010” off a head. Typical piston to valve clearance is at least .080-.100” so you aren’t going to crash the valves into the heads, and while the cam timing will be altered, it won’t be by more than a few degrees, which the computer and the variable valve timing system can easily compensate for, and even if it couldn’t, you could degree the cams by filing away some of the keyway to be able to adjust it back into spec.

  33. Dreamgoat

    Dreamgoat

    Сарын өмнө

    you guys need a tv show together. Never saw such great chemistry.

  34. ray h.

    ray h.

    Сарын өмнө

    Save me Obeiwan, you're my only hope ! lol

  35. Jesse Aldape

    Jesse Aldape

    Сарын өмнө

    Where do you buy your BMW parts

  36. Ball Bounces

    Ball Bounces

    Сарын өмнө

    You should engine swap used SxS can-am Maverick x3 turbo rr they have 195hp and can be modified to handle 500hp

  37. George Zaharia

    George Zaharia

    Сарын өмнө

    11:48 i just skipped, cause of title to see if your guy mentions it... in theory you can swap any parts from any engine... from any other engine that has a similar shape... but you have to keep in mind, density and friction resistance and sure enough temperature resistance... if you aren't driving it like a F1 car... and just ride it along... it should work ... if u start gassing that pedal... it will last u around 10 minutes, or as big the difference is between the two parts resistance wise.

  38. George Martin

    George Martin

    Сарын өмнө

    Hell, just aquire a USED head from a state side boneyard.

  39. coxy ofnewp

    coxy ofnewp

    2 сарын өмнө

    This is what I love about the net - Peeps come together and can make things happen, where as in my youth, I'd have to read books and hope I knew someone.. Great work community

  40. D Wall

    D Wall

    2 сарын өмнө

    Why not use a thicker head gasket and resurface the head?

  41. TheBugmenot2009

    TheBugmenot2009

    2 сарын өмнө

    $10k for new engine installed?

  42. britCpower

    britCpower

    2 сарын өмнө

    What camera do you use ?

  43. ValkyriemBDO

    ValkyriemBDO

    2 сарын өмнө

    DUI THE STRAIGHT EDGE YEEEEEAA

  44. Eric Wes

    Eric Wes

    2 сарын өмнө

    Sorry, I don't care anymore. It's just taking too long, and that annoys me. I'm outta here. Time to catch up on my lockpickinglawyer watching.

  45. Per Ardua ad Astra

    Per Ardua ad Astra

    2 сарын өмнө

    Take the car back to a main dealer to identify the electrical fault.

  46. Per Ardua ad Astra

    Per Ardua ad Astra

    2 сарын өмнө

    Dealers don’t want to replace head gaskets. Only routine servicing.

  47. Justin Y.

    Justin Y.

    2 сарын өмнө

    Every dealer will tell you you need a new engine. Had an old b5 s4 and audi told me it needed a new engine and quoted me 12,000. However, it wasn't passing compression all it need was new gaskets for the V heads. I did the work and parts costed 300$.

  48. bill bergovoy

    bill bergovoy

    2 сарын өмнө

    You should give the scrap metal to other youtubers that melt down meteor and cast it into ingots or other forms

  49. Bruno Miramont

    Bruno Miramont

    2 сарын өмнө

    so good news .... mill the head , thick gasket and keep rolling

  50. trekinseattle

    trekinseattle

    2 сарын өмнө

    The feeler gauge they are using is VERY THICK. .004 thousandths is almost paper thin. .001 feeler gauge is super wobbly crazy thin, you can hardly push it because it will wrinkle. Most blocks are half the warp or less than the head. because the block is at least twice as thick and at least twice as strong. The head warps into a banana shape from overheat. When you surface it that only fixes the bottom. the top where the cams ride is still warped, this will cause the cams to seize, gall the aluminum or ive even seen the cam snap in half because its hardened steel and doesnt like rotating out of round. You can do quick fixes to get rid of a car but an overheat damages EVERYTHING. Warps the valve seats, and sometimes loosens the hardened seats in the aluminum head to the point they fall out later doing catastrophic engine damage, scuffs the pistons that swelled in the cylinder wall, takes the tension out of the piston rings which causes oil consumption, An overheat causes the OIL to thin out enough to loose oil cushioning and allows the rod bearing to contact the crank damaging the bearings. etc. etc. sensors fail early from being super hot. etc... bad bad bad.

  51. killercivic2001

    killercivic2001

    2 сарын өмнө

    this video with all these nice people started to relax me... then, I started to crumple back into a ball while the measurements on the block were taken... I think I need help... I love machines too much hahaha

  52. Christopher Crews

    Christopher Crews

    2 сарын өмнө

    That's an Anthony jeselnik joke. It's pretty good one

  53. martin turner

    martin turner

    2 сарын өмнө

    can you weld the head and machine it back

  54. Roger Hammond

    Roger Hammond

    2 сарын өмнө

    $1000 in parts...and how much in labour? Those guys put in some serious hours!

  55. Jesse Ours

    Jesse Ours

    2 сарын өмнө

    Champaign taste on a beer budget.

  56. Happy Gilmore

    Happy Gilmore

    2 сарын өмнө

    Higher density and a higher stability are a no-brainer especially with the larger diameter valves............... Sometimes you need to research the processes.... The only thing that would surpass gravity casting is 3d printing a new head.. If BMW 3d printed the whole 3 cyl engine it would last atleast a million miles as 3d printing defies alot of laws of physics and the main one being thermal heat expansion and warpage............. Gravity Die Casting Process - Advantages and Applications (learnmech.com)

  57. Didier Mukendi

    Didier Mukendi

    2 сарын өмнө

    LS the b1(T7

  58. barrie Williams

    barrie Williams

    2 сарын өмнө

    I can't believe that it took all the time it did to figure out it was a head gasket problem. The very fact that it took such a short time to get so hot was a dead give away. I've had this problem on an Audi, the solution was. Get the head skimmed then, have a custom made gasket to bring the specs back into tolerance. A lot cheaper than a new engine🤔

  59. Doktor Jeep

    Doktor Jeep

    2 сарын өмнө

    LS6 swap. With supercharger and nitro.

  60. The Fishing Life

    The Fishing Life

    2 сарын өмнө

    Bud Replace the water pump thermostat lines and radiator please. Then get the head finished and use 2 head gaskets to make up the space which I dout you'd even need 2. I have done over 100 m54 overheat complete fixes

  61. David Symalla

    David Symalla

    2 сарын өмнө

    Why are you such a good speaker???? Do you talk in front of people daily for a living? You do an outstanding job. Is it a natural ability or have you honed your speaking acuity over the years?

  62. 44 Hawk

    44 Hawk

    2 сарын өмнө

    Serena head itself takes most of the heat energy I still and not understanding why The Machinist thought that they had was warped particularly badly, which it was not oh, and why he thought that that automatically method the block would be warped. But you end up with a good block. And I had that you can probably shave and put a shim head gasket on. I'm sure that they make them.

  63. ADF360 M

    ADF360 M

    2 сарын өмнө

    Glad I watched this video before commenting on the last video. Your "second opinion guy" should get a gold star for knowing his shit.

  64. Unknowntitan

    Unknowntitan

    2 сарын өмнө

    Bmw are shit cars and absolutely garbage

  65. Docker Andy

    Docker Andy

    2 сарын өмнө

    skim the head.. and use an oversize head gasket ?

  66. Muddy Offroad

    Muddy Offroad

    2 сарын өмнө

    Cut the straight edge down

  67. erleclaire

    erleclaire

    2 сарын өмнө

    It's a little bit of work, but a high school kid could piece it out for you. However that would make you a junk dealer....

  68. Chris CHRaVeN

    Chris CHRaVeN

    2 сарын өмнө

    I call bs on what he is saying. No the way they are manufactured wont make much of a difference at all. Resurfacing the cylinder head by 0.15 mm or by the thinknes of 2 pices of paper will not be a problem at all.

  69. Charles Vaughn II

    Charles Vaughn II

    2 сарын өмнө

    Copper gasket spray it and assemble it! Lol

  70. SLYDIT

    SLYDIT

    2 сарын өмнө

    Just machine the head

  71. braddeicide

    braddeicide

    2 сарын өмнө

    $10k = literally bankrupt, grabs Lamborghini from acreage to pickup repair parts to use in home workshop :)

  72. Youssef Mattar

    Youssef Mattar

    2 сарын өмнө

    If you were in Egypt, your BMW would be working a month ago.

  73. Jacqueline Oldhaver

    Jacqueline Oldhaver

    2 сарын өмнө

    I Still say straighten the head. Then light resurface an put it back together.

  74. Wilson the Medical Marijuana Guy

    Wilson the Medical Marijuana Guy

    2 сарын өмнө

    Love the ending classic Rich 😂

  75. jax l

    jax l

    2 сарын өмнө

    just put 2 gaskets on it itll be fine

  76. Im1stbaby

    Im1stbaby

    2 сарын өмнө

    I think a dui tutorial would be interesting. Drink n teach

  77. pablo rages

    pablo rages

    2 сарын өмнө

    SO do Rich and Sam like each other or hate each other?

  78. Gribbet 4eva

    Gribbet 4eva

    2 сарын өмнө

    I checked out ‘Step Mom’ - why are you promoting a porn star - Cory Chase as your step mom - children watch this channel too!

  79. paul taylor

    paul taylor

    2 сарын өмнө

    Great video Sam, enjoyed it very much.

  80. Joel Marble

    Joel Marble

    2 сарын өмнө

    just started watching you on this BMW car and Steven is a riot.

  81. Juan Maldonado

    Juan Maldonado

    2 сарын өмнө

    Copper sealer

  82. Aks K

    Aks K

    2 сарын өмнө

    I'm just admiring that sexy XF R wow

  83. bouytt guyt

    bouytt guyt

    2 сарын өмнө

    Hilarious that you order parts from Germany when the i8 engine is made in the UK

  84. RL Gaa

    RL Gaa

    2 сарын өмнө

    Sam you gaining weight?

  85. Marco Huertas

    Marco Huertas

    2 сарын өмнө

    Do you always look like a homeless guy!!

  86. the dark side

    the dark side

    2 сарын өмнө

    2 head gaskets stacked works I've done it

  87. Luís Aguiar

    Luís Aguiar

    2 сарын өмнө

    yeahhhh you found the most common solution in 3rd world countries... dope

    • bouytt guyt

      bouytt guyt

      2 сарын өмнө

      Where’s the videos ! Your so lazy

  88. nortious maximus

    nortious maximus

    2 сарын өмнө

    what about a solid copper gasket, someone with a water jet, or a or a cnc laser cutter, could cut one from a sheet of copper. if you plane the head, use a thicker piece of copper sheet to make the gasket, the head and or the block, can also be machined for a stainless steel fire ring, in case the copper gasket is not up to the job, it works on dragsters, and high horse power turbo cars, where boost pressure could lift a regular gasket.

  89. Siri Fail

    Siri Fail

    2 сарын өмнө

    Woah, what’s the finish on the red car?

  90. Farrukh Kiani

    Farrukh Kiani

    2 сарын өмнө

    Hi Sam. Why is it taking too long? If it still doesn't work, gift it to the "Raasta Man"

  91. Mechanic Taft

    Mechanic Taft

    2 сарын өмнө

    #not a SUPERCAR #NEVER WILL BE A SUPERCAR #STUPIDCAR SLOWER THAN YOUR INTELLECT!!!!!!!!!

  92. jckrarup

    jckrarup

    2 сарын өмнө

    Why couldnt you have the head milled and use a thicker head hasket or even two? People do this all the time if you need to lower the compression.

  93. John Bishop

    John Bishop

    2 сарын өмнө

    I am really confused, what’s the silliness with your “stepmom”,I find it a bit sick. Is the Richie thing just a joke ? As a “ friend” he worries me, he is just too weird to be normal. A permanent chicken died cannot be doing him and good.

  94. Anthony Fazin

    Anthony Fazin

    2 сарын өмнө

    I need an updated video Sam, I’ve been waiting a week, come on brother haha.

  95. Peter P.

    Peter P.

    2 сарын өмнө

    old TDI Diesel owners going through this all the time ,warped heads ,engines going ok even after 5 years resurfacing and thicker head gasket. pressure is much less in petrol cylinders ,even with original head this could work

  96. Constitutional Logic

    Constitutional Logic

    2 сарын өмнө

    I would question the first machine shops diag. First they didn't clean the head first, second the small about warpage would not effect the timing, the ecm is smart enough to compensate. And the thicker head gasket is even better. Not to mention once the head is torqued to spec you would be surprised how much it can change the shape/flatness of the surface.

  97. ABHISHEK

    ABHISHEK

    2 сарын өмнө

    Hey Sam where is another part waiting since last week 😡

  98. SuperDancingdonkey

    SuperDancingdonkey

    2 сарын өмнө

    All these short cuts for a car that even without problems won't even get to 100k miles without falling apart. I don't know how anyone could live with themselves making a profit selling something they know is already trashed.

  99. SuperDancingdonkey

    SuperDancingdonkey

    2 сарын өмнө

    Conman

  100. Rick Pontificates

    Rick Pontificates

    2 сарын өмнө

    Well you got that right! A Mini Cooper IS SCRAP

Дараах